Middleby Marshall PS540 Installation Manual download pdf (Page 13)

SECTION 2

INSTALLATION

SECTION 2

INSTALLATION

NOTE: In U.S.A., the oven installation must conform with

local codes, or in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1 latest edition. The

oven, when installed, must be electrically grounded in

accordance with local codes, or in the absence of local

codes, with the National Electrical Code (NEC), or

ANSI/NFPA70.

NOTE: In Canada, the oven installation must conform with

local codes, or in the absence of local codes, with the

Natural Gas Installation Code, CAN/CGA-B149.1, or the

Propane Gas Installation Code, CAN/CGA-B149.2, as

applicable. The oven, when installed, must be electrically

grounded in accordance with local codes, or in the ab-

sence of local codes, with the Canadian Electrical Code

CSA, C22.2, as applicable.

NOTE: For Australian installation, the oven must be

installed only by an authorised person in accordance with

AS5601, local authority, gas, electricity, any applicable

statutory regulations and manufacturer requirements.

NOTE

There must be adequate clearance between

the oven and any adjacent combustible con-

struction. Clearance must also be provided

for servicing and for operation.

CAUTION

It is required that the oven be placed under a

ventilation hood for adequate air supply and

ventilation.

CAUTION

Do not obstruct the flow of combustion and

ventilation air to and from your oven. Do not

obstruct the ventilation holes in the Control Panel.

CAUTION

On ovens with the Machinery Drive Compartment

located at the right end, a minimum clearance of 0″

to a left side wall, 18″ to a right side wall and 6″ from

a back wall to air openings at the rear of the oven

must be maintained. On ovens with the machinery/

drive compartment located at the left end, a mini-

mum clearance of 0″ to a right side wall, 18″ to a left

side wall and 6″ from a back wall to air openings at

the rear of the oven must be maintained.

For servicing and cleaning, a minimum of 18″

clearance from all walls is recommended.

I. UNLOADING

Your Middleby Marshall PS540-Series Oven is shipped

partially assembled. It will arrive in a carton on a crate.

Carton size for a PS540-Series Oven is:

84″ (2134mm) Long ×

58″ (1473mm) Wide ×

44″ (1118mm) High ×

The crate and carton must be examined before signing the

Bill of Lading. Report any visible damage to the transport

company, and check for the proper number of crates. If

apparent damage is found, make arrangements to file a

claim against the carrier. Surface Interstate Commerce

Regulations (U.S.A.) require that the claim must be

initiated by the consignee within 10 days from the date that

the shipment is received.

A Pre-installation Procedures Manual (MM P/N 88910-0009)

is attached to the exterior wall of the carton. This manual

contains detailed instructions on unpacking and moving the

oven(s) to the operating site. When the transport company

notifies you of an impending delivery, arrange to have a forklift

at your facility to unload the carton(s).

Instructions for stacking the ovens is continued in a

separate manual used by Middleby Marshall Authorized

Installers.

If you have a door wider than the carton, simply move the

carton into your facility and arrange an appointment with

your Middleby Marshall Authorized Installer.

If your door is narrower than the carton, then the oven will

have to be unpacked. Follow the directions shown in the

Pre-Installation Procedures Manual.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 75 76

Comments to this Manuals

No comments

Middleby Marshall PS540 Installation Manual Page 13

Comments to this Manuals

Related products and manuals for Ovens Middleby Marshall PS540