Middleby Marshall PS540 Installation Manual download pdf (Page 30)

SECTION 3

OPERATION

WARNING

OVEN MUST BE KEPT CLEAR OF

COMBUSTIBLES AT ALL TIMES.

III. STEP-BY-STEP OPERATION

Control Panel (On split belt ovens, two conveyor speed

controls are mounted on the control panel.)

A. Startup Procedures

Initial Startup

Check that the full-flow gas shutoff valve is “on”.

This valve is located outside the rear of the oven. See

Figures 2-3, 2-4, and 2-5.

Daily Startup

1. Turn the BLOWER switch (Figure 3-6) to the “ON” or “I”

position. This starts the main blower fan and the cooling

fan. The blower circulates air through the air fingers and

must stay on during the cooking or baking process.

2. Check to see if the cooling fan (see Figure 1-8) is

operating when the blower switch (see Figure 3-6) is turned

“ON” or “I”. The cooling fans cool the control components

and burner blower motor. The cooling fan, located at the

rear of the electrical control cabinet blows air into and

through the cabinet. Air is exhausted through the front of

the cabinet and also out the front of the oven. Refer to Daily

Maintenance Section for fan intake checking procedure.

IMPORTANT NOTE

The cooling fan operates when the BLOWER

switch is turned “ON” or “I”. It must operate to keep

the control console below 140°F (60°C).

3. Turn the CONVEYOR switch (Figure 3-6) to the “ON” or

“I” position. This starts the conveyor belt moving through

the oven. Set the conveyor speed for the desired baking

time. Refer to the following Procedures E, F and G.

4. Set the temperature controller to the desired baking

temperature. See section on bake times to determine

desired temperature.

NOTE: For complete temperature controller operation

instructions refer to Step C.

5. Turn the HEAT switch (Figure 3-6) to the “ON” or “I”

position. This completes a circuit to supply electric power

to the burner. When an oven that has not been in operation

for approximately 1/2 hour is turned on, it goes through a

30-second purge cycle. The burner blower motor will not

operate during the time the blower fan is purging the oven.

After 30 seconds, the burner blower motor starts, which

can be detected by feeling a slight vibration when touched.

This permits the burner to light.

When in operation, the burner is either on low or high flame.

Its flame-sensing electrode must be satisfied to keep the

bypass and gas valves open. If for some reason the

bypass flame is extinguished, the burner tries to relight for

90 seconds. If the burner flame does not relight in 90

seconds, the oven goes into automatic safety lockout.

To relight the oven, turn the HEAT switch to “OFF” or “O”

for 5 minutes. Then, repeat the Oven Startup procedure.

6. Close front window.

7. Oven will reach a baking temperature of 600°F (315°C)

in approximately 10 minutes. Allow the oven to cycle for

30 minutes after it has reached desired bake temperatue.

The oven is now ready for baking.

Power Failure

In case of power failure, turn off all switches; open oven

window and remove product. After power has been

reestablished follow normal startup procedure.

CAUTION

The burner will not operate and gas will not flow

through the burner without electric power. No

attempt should be made to operate the oven

during power failure.

B. Shutdown Procedure

1. Turn the BLOWER and HEAT switches to “OFF” or “O”.

NOTE: The blowers will remain on until the oven tempera-

ture cools down to 200°F (93°C) at which time they will stop

automatically.

2. Make certain that there are no products left on the

conveyor inside the oven. Turn the CONVEYOR switch

to “OFF” or “O”.

3. Turn off the main gas supply valve.

4. Open the oven window.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 75 76

Comments to this Manuals

No comments

Middleby Marshall PS540 Installation Manual Page 30

Comments to this Manuals

Related products and manuals for Ovens Middleby Marshall PS540